$ telnet 10.1.1.2
Login Screen
============
User Name: admin
Password:# show vlan
Vlan Name Ports Type Authorization
---- ----------------- --------------------------- ------------ -------------
1 1 g(1-4),ch(1-8) other Required
10 LAN g(1-4,13-24) permanent Required
192 wifi g(1,12) permanent Required
203 DMZ g(1-11) permanent RequiredThen, when you get to the main menu, press Ctrl + Z on your terminal.
Switch Main Menu
================
1. System Configuration Menu
2. Port Status
3. Port Configuration
4. System Mode (Layer 2 / Layer 3)
5. Help
0. logout
ArrowKey/TAB/BACK=Move SPACE=Toggle ENTER=Select ESC=Back
>Now you should get to a prompt that has a couple of options.
>?
Unknown parameter
May be one from the following list:
debug exit help lcli logout mcli menu
>From here, we want to launch the lcli application. When we have done so, we will be asked to login.
>lcli
User Name:admin
SRW2024#Now we arrive at a VERY Cisco-ish console. It follows the Cisco command set (mainly). Using a ? to view available options, we get:
SRW2024#
clear Reset functions
clock Manage the system clock
configure Enter configuration mode
copy Copy from one file to another
crypto Cryptographic commands
debug-mode Exit from the EXEC to debug mode
delete Delete a file from the flash file system
disable Disable privileged commands
dot1x 802.1x EXEC commands
exit Exit from the EXEC
help Description of the interactive help system
login Exit from the EXEC and Log in
no Negate command
ping Send echo messages
reload Halt and perform a cold restart
resume Resume telnet session.
set Set System Parameters
show Show running system information
telnet Open telnet session.
terminal Set current session functions
test diagnose
traceroute Discover the routes to destination
SRW2024#You can use these commands to configure the switch, change port settings, and gather information about the switch configuration.
SRW2024# show ver
SW version 1.2.2 ( date 28-Jan-2007 time 13:48:36 )
Boot version 1.0.1 ( date 11-Jun-2006 time 18:43:59 )
HW version 00.03.00
SRW2024#
SRW2024# show interfaces status
Flow Link Back Mdix
Port Type Duplex Speed Neg ctrl State Pressure Mode
-------- ------------ ------ ----- -------- ---- ----------- -------- -------
g1 1G-Copper Full 100 Enabled Off Up Disabled On
g2 1G-Copper Full 1000 Enabled Off Up Disabled On
g3 1G-Copper Full 1000 Enabled Off Up Disabled Off
g4 1G-Copper -- -- -- -- Down -- --
g5 1G-Copper -- -- -- -- Down -- --
g6 1G-Copper Full 1000 Enabled Off Up Disabled On
g7 1G-Copper -- -- -- -- Down -- --
g8 1G-Copper -- -- -- -- Down -- --
g9 1G-Copper -- -- -- -- Down -- --
g10 1G-Copper -- -- -- -- Down -- --
g11 1G-Copper -- -- -- -- Down -- --
g12 1G-Combo-C -- -- -- -- Down -- --
g13 1G-Copper -- -- -- -- Down -- --
g14 1G-Copper -- -- -- -- Down -- --
g15 1G-Copper -- -- -- -- Down -- --
g16 1G-Copper -- -- -- -- Down -- --
g17 1G-Copper -- -- -- -- Down -- --
g18 1G-Copper Full 100 Enabled Off Up Disabled On
g19 1G-Copper -- -- -- -- Down -- --
g20 1G-Copper Half 10 Enabled Off Up Disabled Off
g21 1G-Copper -- -- -- -- Down -- --
g22 1G-Copper -- -- -- -- Down -- --
g23 1G-Copper -- -- -- -- Down -- --
g24 1G-Combo-C -- -- -- -- Down -- --
Flow Link
Ch Type Duplex Speed Neg control State
-------- ------- ------ ----- -------- ------- -----------
ch1 -- -- -- -- -- Not Present
ch2 -- -- -- -- -- Not Present
ch3 -- -- -- -- -- Not Present
ch4 -- -- -- -- -- Not Present
ch5 -- -- -- -- -- Not Present
ch6 -- -- -- -- -- Not Present
ch7 -- -- -- -- -- Not Present
ch8 -- -- -- -- -- Not Present
SRW2024#
SRW2024# show vlan
Vlan Name Ports Type Authorization
---- ----------------- --------------------------- ------------ -------------
1 1 g(1-4,9-16,21-24),ch(1-8) other Required
10 LAN g(1-4,17-20) permanent Required
203 DMZ g(1-8) permanent Required
SRW2024#You can go into configuration mode by simply using the configure command.
SRW2024# configure
SRW2024(config)#
aaa Authentication, Authorization and Accounting is used
to manage user access to the system
arp Set a static ARP entry
bridge Global Bridge table configuration commands
class-map This command create class map and enter class map
configuration mode.
Use no form in order to delete the class.
clock Manage the system clock
crypto Global cryptographic features configuration subcommands
do execute an EXEC-level command
dot1x Global Configuration Commands for 802.1x
enable Modify enable password parameters.
end Exit from configure mode
exit Exit from configure mode
file-system File system configuration command
gvrp Global GVRP configuration commands
help Description of the interactive help system
hostname Set system's network name
interface Select an interface to configure
ip IP configuration
lacp Global IEEE 802.3 link aggregation commands
line To identify a specific line for configuration
lldp Configure LLDP protocol
logging Configure message logging facilities.
mac MAC access lists commands
management IP management
no Negate command
policy-map This command create policy map and enter policy map
configuration mode. Use no form to delete the policy
map.
port switch ports configuration
priority-queue Set priority queue parameters
qos Enable/Disable QoS on the device and enter the QoS
mode (advance/basic/service).
radius-server Modify RADIUS parameters
rmon Remote Monitoring (RMON) configuration subcommand
service Service commands.
snmp-server SNMP and system commands.
sntp Global Simple Network Time Protocol (SNTP)
configuration subcommands
spanning-tree Configure Spanning Tree Subsystem
tacacs-server TACACS server command
username Establish User Name Authentication.
vlan Vlan commands
wrr-queue Configure queue drop mechanism on egress port.
SRW2024(config)#As you can see, everything looks VERY Cisco. For those familiar with setting up Cisco switches, finding your way around this console mode in the SRW2024 will be fairly easy – with only a few variations on the \”Cisco method\” of configuration. So, enjoy your no longer useless serial, SSH, and telnet configuration of your SRW2024 switch and get the most out of this excellent piece of hardware! EDIT: Will add to this as I use the switch more via CLI.
Basic Reference Guide
Configure VLAN
1) Create the vlan in the database:
# configure
(config)# vlan database
(config-vlan)# vlan 993 (enter your VLAN ID of choice here)
(config-vlan)# end2) Add a switchport to the VLAN: untagged
# configure
(config)# interface ethernet g1
(config-if)# switchport access vlan 993
(config-if)# endtagged (Repeat for each allowed vlan)
# configure
(config)# interface ethernet g1
(config-if)# switchport general allowed vlan add 993
(config-if)# endShow Port Config:
# show interfaces configuration ethernet g1
Flow Admin Back Mdix
Port Type Duplex Speed Neg control State Pressure Mode
-------- ------------ ------ ----- -------- ------- ----- -------- ----
g1 1G-Copper Full 1000 Enabled Off Up Disabled AutoShow port configuration
# show interfaces switchport ethernet g1
Port : g1
Port Mode: General
Gvrp Status: disabled
Ingress Filtering: true
Acceptable Frame Type: admitOnlyVlanTagged
Ingress UnTagged VLAN ( NATIVE ): 1
Protected: Disabled
Port is member in:
Vlan Name Egress rule Port Membership Type
---- -------------------------------- ----------- --------------------
1 1 Untagged System
10 LAN Tagged Static
192 wifi Tagged Static
203 DMZ Tagged Static
Forbidden VLANS:
Vlan Name
---- --------------------------------
Classification rules:
SRW2024#Show vlan config
# show vlan
Vlan Name Ports Type Authorization
---- ----------------- --------------------------- ------------ -------------
1 1 g(1-4),ch(1-8) other Required
10 LAN g(1-4,13-24) permanent Required
192 wifi g(1,12) permanent Required
203 DMZ g(1-11) permanent Required